Product Name: |
50 x 26 mm low cost controller |
Description: |
The series of single loop controllers with a single LED display are used for non-sophisticated system, state-of-art design, sufficient features, easy for operation and low-cost.
|
Features: |
‧ Easy-to-use
‧ Fuzzy modified PID heat & cool control
‧ Fast A-D sampling rate (5 times/s)
‧ Universal input (PT100, thermocouple)with high accuracy 18-bit A-D
‧ Analog output (linear current or voltage)uses high accuracy 15-bit D-A
‧ RS-485 RS-232 interface
‧ Programming port provided on board
‧ Support manual control & auto-tune function
‧ Wide variety of alarm mode selection
‧ Lockout protection control
‧ Bumpless transfer during failure mode
‧ Soft-start ramp and dwell timer
‧ Bright display stabilized with digital filter
‧ Front panel sealed to NEMA 4X & IP65(model C21)
‧ UL/CSA/CE approval
‧ High performance with low cost
|
Specification: |
Power
90 - 250 VAC, 47 - 63 Hz, 10VA, 5W maximum
11 - 26 VAC / VDC, SELV, Limited Energy, 10VA, 5W maximum
Signal Input
Resolution : 18 bits
Sampling Rate : 5 times / second
Maximum Rating : -2 VDC minimum, 12 VDC maximum( 1 minute for mA input )
Temperature Effect : ±1.5 uV/ °C for all inputs except mA
input ±3.0 uV/ °C for mA input
Sensor Lead Resistance Effect :
T/C: 0.2uV/ohm
3-wire RTD: 2.6 °C/ohm of resistance difference of two leads
2-wire RTD: 2.6 °C/ohm of resistance sum of two leads
Burn-out Current : 200nA
Common Mode Rejection Ratio ( CMRR ) : 120dB
Normal Mode Rejection Ratio ( NMRR ) : 55dB
Sensor Break Detection :
Sensor open for TC, RTD and mV inputs,
Sensor short for RTD input,
below 1 mA for 4-20 mA input,
below 0.25V for 1 - 5 V input, unavailable for other inputs.
Sensor Break Responding Time :
Within 4 seconds for TC, RTD and mV inputs,
0.1 second for 4-20 mA and 1 - 5 V inputs.
Characteristics :
| Type |
Range |
Accuracy@
25 °C |
Input
Impedance |
| J |
-120 ~ 1000 °C
(-184 ~ 1832 °F)
|
±2 °C |
2.2MΩ |
| K |
-200 ~ 1370 °C
(-328 ~ 2498°F) |
±2 °C |
2.2MΩ |
| T |
-250 ~ 400°C
(-418 ~ 752°F) |
±2 °C |
2.2MΩ |
| E |
-100 ~ 900 °C
(-148 ~ 1652 °F) |
±2 °C |
2.2MΩ |
| B |
0 ~ 1800 °C
(32 ~ 3272 °F) |
±2 °C
(200°C - 1800°C) |
2.2MΩ |
| R |
0 ~ 1767.8 °C
(32 ~ 3214 °F) |
±2 °C |
2.2MΩ |
| S |
0 ~ 1767.8 °C
(32 ~ 3214 °F) |
±2 °C |
2.2MΩ |
| N |
-250 ~ 1300 °C
(-418 ~ 2372 °F) |
±2 °C |
2.2MΩ |
| L |
-200 ~ 900 °C
(-328 ~ 1652 °F) |
±2 °C |
2.2MΩ |
| PT100
(DIN) |
-210 ~ 700 °C
(-346 ~ 1292 °F) |
±0.4°C |
1.3KΩ |
| PT100
(JIS) |
-200 ~ 600 °C
(-328 ~ 1112 °F) |
±0.4°C |
1.3KΩ |
| mV |
-8 ~ 70mV |
±0.05% |
2.2MΩ |
| mA |
-3 ~ 27mA |
±0.05% |
70.5Ω |
| V |
-1.3 ~ 11.5V |
±0.05% |
650KΩ |
Output 1 / Output 2
Relay Rating : 2A/240 VAC, life cycles 200,000 for resistive load
Pulsed Voltage : Source Voltage 5V, current limiting resistance 66Ω .
Linear Output Characteristics:
| Type |
Zero
Tolerance |
Span
Tolerance |
Load
Capacity |
| 4-20 mA |
|
20-21 mA |
500Ω max. |
| 0-20 mA |
0 mA |
20-21 mA |
500Ω max. |
| 0-5 V |
|
5-5.25 V |
10KΩ min. |
| 1-5 V |
0.9-1 V |
5-5.25 V |
10KΩ min. |
| 0-10 V |
0 V |
10-10.5 V |
10KΩ min. |
Linear Output
Resolution : 15 bits
Output Regulation : 0.02 % for full load change
Output Settling Time : 0.1 sec. ( stable to 99.9 % )
Isolation Breakdown Voltage : 1000 VAC
Temperature Effect : ±0.01 % of SPAN / °C
Triac ( SSR ) Output
Rating : 1A / 240 VAC
Inrush Current : 20A for 1 cycle
Min. Load Current : 50 mA rms
Max. Off-state Leakage : 3 mA rms
Max. On-state Voltage : 1.5 V rms
Insulation Resistance : 1000 Mohms min. at 500 VDC
Dielectric Strength : 2500 VAC for 1 minute
Alarm( Output 2 )
Alarm Relay :Form A,Max. rating 2A/240VAC, life cycles 200,000 for resistive load.
Alarm Functions : Dwell timer,
Deviation
High / Low Alarm,
Deviation Band High / Low Alarm
Process High / Low Alarm
Alarm Mode : Normal, Latching, Hold, Latching / Hold.
Dwell Timer : 0.1 - 4553.6 minutes
Data Communication
Interface : RS-232 ( 1 unit ), RS-485 ( up to 247 units )
Protocol : Modbus Protocol RTU mode
Address : 1 - 247
Baud Rate : 2.4 ~ 38.4 Kbits/sec
Data Bits : 7 or 8 bits
Parity Bit : None, Even or Odd
Stop Bit : 1 or 2 bits
Communication Buffer : 160 bytes
Analog Retransmission
Output Signal : 4-20 mA, 0-20 mA, 0-1V, 0-5V, 1-5V, 0-10V
Resolution : 15 bits
Accuracy : ±0.05 % of span ±0.0025 %/ °C
Load Resistance : 0 - 500 ohms ( for current output ),10 K ohm minimum ( for voltage
output )
Output Regulation : 0.01 % for full load change
User Interface
Single 4-digit LED Displays :10mm (C21, C91)
Keypad : 3 keys(C21), 4 keys(C91)
Programming Port : For automatic setup, calibration and testing
Communication Port : Connection to PC for supervisory control
Control Mode
Output 1 : Reverse ( heating ) or direct ( cooling )action
Output 2 : PID cooling control, cooling P band 50 ~ 300% of PB, dead band -36.0
~ 36.0% of PB
ON-OFF : 0.1 - 90.0 ( °F ) hysteresis control ( P band = 0 )
P or PD : 0 - 100.0 % offset adjustment
PID : Fuzzy logic modified , Proportional band 0.1 ~ 900.0°F ,
Integral time 0 - 3600 seconds , Derivative time 0 - 360.0 seconds
Cycle Time : 0.1 - 90.0 seconds
Manual Control : Heat (MV1) and Cool (MV2)
Auto-tuning : Cold start and warm start
Failure Mode : Auto-transfer to manual mode while sensor break or A-D converter damage
Ramping Control : 0 ~ 900.0°F/minute or 0 ~ 900.0 °F/hour ramp rate
Sleep Mode : Enable or Disable
Ramping Control : 0 ~ 500.0 °C/minute or 0 ~ 500.0 °C/hour ramp rate
Digital Filter
Function : First order
Time Constant : 0, 0.2, 0.5, 1, 2, 5, 10, 20, 30, 60 seconds programmable
Environmental & Physical
Operating Temperature : -10°C to 50°C
Storage Temperature : -40°C to 60°C
Humidity : 0 to 90 % RH ( non-condensing )
Altitude : 2000m maximum
Pollution : Degree 2
Insulation Resistance : 20 Mohms min. ( at 500 VDC )
Dielectric Strength : 2000 VAC, 50/60 Hz for 1 minute
Vibration Resistance : 10 - 55 Hz, 10 m/s² for 2 hours
Shock Resistance : 200 m/s² ( 20 g )
Moldings : Flame retardant polycarbonate
Dimensions :
C21 ---50mm(W) X 26.5mm(H) X 110.5mm(D), 98.0 mm depth behind panel
C91 ---48mm(W) X 48mm(H) X 94mm(D), 86 mm depth behind panel
Mounting:
C21 ---panel mount, cutout 22 X 45( mm )
C91 ---panel mount, cutout 45 X 45 ( mm )
Weight :
C21 --- 120 grams
C91 --- 140 grams
Approval Standards
Safety : UL 61010C-1 , CSA C22.2 No. 24-93 , EN61010-1 (IEC1010-1)
Protective Class :
NEMA 4X ( IP65 ) front panel for C21,
IP30 front panel for C91, all indoor use,
IP20 housing and terminals
EMC : EN61326
|
Other Description: |
C21 - □□□□□□
1 2 3 4 5 6
1 Power Input
4:
90 - 250 VAC, 47-63 HZ
5:
11 - 26 VAC or VDC, SELV, Limited Energy
2 Signal Input
1: Standard Input
Thermocouple: J, K, T, E, B, R, S, N, L
RTD: PT100 DIN, PT100 JIS
2:
0 - 60 mV
3:
0 - 1 V
4:
0 - 5 V
5:
1 - 5 V
6:
4 - 20 mA
7:
0 - 20 mA
8:
0 - 10V
9: Special Order
3 Output 1
0: None
1: Relay rated 2A / 240VAC
2: Pulsed voltage to drive SSR, 5V / 30mA
3: Isolated 4 - 20mA / 0 - 20mA
4: Isolated 1 - 5V / 0 - 5V
5: Isolated 0 - 10V
6: Triac output 1A / 240VAC,SSR
C:
Pulsed voltage to drive SSR, 14V/40mA
9: Special order
4 Output 2
0: None
1: Form A relay 2A / 240VAC
2: Pulsed voltage to drive SSR, 5V / 30mA
3: Isolated 4 - 20mA / 0 - 20mA
4: Isolated 1 - 5V / 0 - 5V
5: Isolated 0 - 10V
6: Triac output, 1A / 240VAC, SSR
7: Isolated 20V / 25mA transducer power supply
8: Isolated 12V / 40mA transducer power supply
9: Isolated 5V / 80mA transducer power supply
A:
RS-485 interface (for C91)
C:
Pulsed voltage to drive SSR, 14V/40mA
D:
Retransmit 4-20mA / 0-20mA (for C91)
E:
Retransmit 1-5V / 0-5V (for C91)
F:
Retransmit 0-10V (for C91)
B:
Special order
5 Communications
0: None
1: RS-485 interface
2:
RS-232 interface(for C21)
3:
Retransmit 4 - 20 mA / 0 - 20 mA(for C21)
4:
Retransmit 1 - 5V / 0 - 5V(for C21)
5:
Retransmit 0 - 10V(for C21)
9: Special order
6 Display Color
0:
Red color
1:
Green color
|
|
|
|
| This is the details for C21, 50 x 26 mm low cost controller. The information includes model, name, description and specification for C21, 50 x 26 mm low cost controller. Related Keywords : low cost controller |
|
